Buzzweld's Rust encapsulator combats corrosion, and its ability to return by tackling the causes of corrosion in several ways.
Rust Encapsulator Chassis Primer
Rust Encapsulator is a development of our previous products, such as RCP (Rust Control Primer), FCP (Fast Cure Primer), and FE (Fluid Etch). we have combined the strengths of these three products into one taking the corrosion stabilisation from RCP, the cure time and compatibility from FCP, and the adhesion and durability of Fluid etch to create a product that is a world ahead of any primer we have offered to date.
Suitable for use as a high adhesion primer for other products like Chassis paints, Underseals, waxes, and other automotive coatings as part of a Rustproofing Solution.
- By stabilising corrosion from Fe203 (rust), to magnetite we remove the reactivity of not only the corrosion itself, but we reduce it BELOW that of bare steel. This means even if you removed our coating, the stabilised corrosion will degrade at a REDUCED rate vs bare steel. By doing this we reduce the ability of the part you are protecting to degrade further.
- Rust Encapsulator is infused with Glass Flake. Upon application the flake will spread throughout the coating, prior to setting. What you are left with is a coating with evenly spaced toughened glass particles. These not only massively increase abrasive resistance and hardness, but they also create a convoluted path through the coating that moisture, and contaminents will have to travel to re activate the corrosion, add to that the corrosion will have been stabilised by the above, and you now have three layers of protection from a single coating.
- Rust Encapsulator does not suffer from porousity, so you can protect without the requirement to then protect the primer saving money.
- Minimal Prep. Remove loose rust/ paint, degrease and apply.
- Rust Encapsulator is compatible with most top coats, can be applied to rusty or most bare metals.
- High adhesion, semi self-etching can be used under and over body fillers, under lacquer, enamels, urethanes, most fast cure coatings.
- High build so will fill in small preparation and substrate defects.
- Will not fail due to UV degredation
- ZERO rust creep product. One of the fastest ways for corrosion to beat oxides, zinc, and otehr coatings is to blister and force the coating off. Rust Encapsulator is specifically designed to stop this, which means not only are you protected, but if perforation does occur, the damage is localised and limited from spreading.
- VERY fast cure. touch dry in as little as 15 minutes.
- Always apply minimum two coats. For aerosols going to bare/ blasted/ rusty steel we recommend 4>5 coats due to aerosols having an average of 75% more shrinkback.
- Rust Encapsulator Chassis Primer
PRODUCT TYPES
- PLATINUM- The highest grade of RE (Previously Stage 3)- Infused with our compound to assist with :-
- Sound Deadening -RE Now limits sound transfer
- RE Platinum has increased porosity resistance
- Resonance Suppression -RE Now actively combats resonance produced from panels
- Thermal Insulative properties -RE now significantly limits heat loss, and reduces energy required to keep a cab cool.
- Ceramic -RE is now more resistant to abrasion, gouging and has increased longevity due to increased porosity resistance
By selecting the Platinum option you are purchasing the highest grade of RE we can produce. For ultimate sound and thermal insulation we recommend applying Cosyfoam over RE.
Thinning
Product Types
1000ml Paint Tin
Normal paint tin for brush / roller / thinning and spraying
1000ML Schutz Undercoating Tin
Stubby Schutz Tin. These tins work with our FX10 Spraygun, FX11 Spraygun & FX12. The gun screws directly on. To use a normal Schutz gun with a stubby schutz tin, You need to trim the pickup tube 75mm shorter. 500ML Stubby Shorts Schutz
Stubby Shorts Schutz. These tins work with our FX10 Spraygun, FX11 Spraygun & FX12. The gun screws directly on. A normal schutz gun can be used if you cut the pickup tube down by 110mm
5000ml Paint Tin
Normal paint tin for brush / roller / thinning and spraying
400ML Aerosol (traditional)
Traditional aerosol.
400ML Buzzweld Powercan The Aerosol powercan uses NO THINNER. as a result the can outputs the same amount of paint as a spraygun. This means less coats, a much higher film build and time saved. HOWEVER- the cans empty themselves very quickly. Protection VS coverage. When using a powercan you need to spray from further away. This can can also be used as a textured spray (comes with two nozzles).
27 September 2024 | Andrew
Bought this to use on my Hilux and was impressed with how it went on and the coverage. Did my research on the forums and I can see why it gets recommended!
Was this helpful to you? Yes / No
02 September 2024 | David
Great product, applies nicely and seems to adhere very well. Time will tell how it performs but as I'm coating with the CIO as a top coat hopefully it stands the test of time!
1 of 1 people found this review helpful.
Was this helpful to you? Yes / No
30 August 2024 | Kevin
I’ve yet to use the product but hoping for good things. In regards of service I opted for standard delivery as shipping is so expensive these days but still received the item next day. Buzzweld indicate this is typical but obviously cannot guarantee it, always nice to be surprised by better service than expected. Will be happy to deal with this supplier again.
Was this helpful to you? Yes / No
PREFER BUZZWELD RUST ENCAPSULATOR TO EASTWOOD OR POR 12 August 2024 | Jason
Been looking far and wide for a quality chassis primer for my Jimny.
I've tried POR. Expensive and a right ballache to get the 3 stage process right.
Then tried Eastwood Encapsulator. Again expensive and a pig to stop it going off in the tin. Better results tho.
Then stumbled across Buzzwelds website with its wealth of product info and how to guides so I took a punt on the Ecapsulatore Blackit Kit. Followed the advice regarding stripe coating the edges after stripping back the scabby rust. Very thick red oxide style paint. Got to work it into the pits and corners etc over several coats but it has a high grab and does tend to run on vertical sides. All in, I'm pleased with the quality and cost compared to the US equivalent. Not yet ready for the Blackit application but will review as I work round each corner of the car.
Also I'm happy with the Buzzweld experience. I had an issue with the delivery which was immediately rectified. Highly recommended company.
Was this helpful to you? Yes / No
23 July 2024 | Shaun
I’m renovating my 2007 landrover discovery 3 and was recommended to use this product by a couple of friends and it’s living up to everything they said about it after pressure washing and cup brushing the chassis and under floor it’s the ideal primer I used a brush on method and a couple of spray cans for the hard to reach areas. Then followed up with CIO the underside is looking fully rejuvenated.
1 of 1 people found this review helpful.
Was this helpful to you? Yes / No
08 July 2024 | Rob
Brilliant product, great service & knowledge!
Was this helpful to you? Yes / No
23 May 2024 | Nicole
The product is exactly as described and arrived in good condition. Having paid £15 delivery to Moray, I was expecting to receive it quicker than I did. It was still quicker than my partner's order from the same seller via Ebay, which took almost 2 weeks to arrive.
Was this helpful to you? Yes / No
Response:
Hi Nicole, we had a delay on Re materials. Fiurst time in 15 years. All sorted now. Kind regards, Craig.
10 May 2024 | Lawrence
Best stuff in the world picked up my first tin hopeful it would work, did it? You bet it did I've been dremeling the rusty bits for over two yrs and it's been do a bit with the Dremel brush on RE a couple of weeks later do another bit 2yrs on the bits I've done zero rust return and I've still been driving her most weeks
4 of 4 people found this review helpful.
Was this helpful to you? Yes / No
06 May 2024 | Paul
Easy to use in a spray can format, dries well and appears to do the job perfectly
Was this helpful to you? Yes / No
03 May 2024 | Henry
I used two coats on the chassis of my T5, it was easy to apply and left a great finish ready for the WAR superwax. Thanks.
Was this helpful to you? Yes / No
Read all 88 customer reviews...
